Endurance matters:
Up to 2X for SD and micro SD cards!

09_ATP_2-facheEndurance_720px

Designed for write-intensive applications. Designed with high endurance, low latency for long-life data storage. The new SD/microSD Card series S650 and S750 from ATP achieve real top values. This becomes especially clear in direct comparison with cards of the same configuration:

  • 1.6 times higher endurance in native 3D triple-level cell (TLC) mode
  • 2 times higher endurance in pseudo single-level cell (pSLC) mode

The SD or microSD cards meet the needs of dashcams and digital video recorders (DVRs) as well as surveillance systems, autonomous vehicles and other demanding applications. The memory cards are built for the rigors of non-stop video recording.

High endurance with over 109,000 hours of recording time in native TLC
Video evidence can prove to be "mission-critical" in many scenarios. Therefore, it is very important that SD/microSD cards can record continuously without compromising image quality and integrity.

The S650 series can record Full HD video for up to 109,401 hours continuously (in ring buffer) - far longer than comparable cards marketed as "High Endurance". Its 5K program/erase (P/E) cycles rating translates to 1.6X higher endurance. The S750 Series, configured as pseudo single-level cell (pSLC) is rated for 60K P/E cycles, or 2 to 3X higher endurance.

Ready for recording in under 1 second
Endurance is not the only advantage card of the new ATP SD cards. After power-on, drive recorders may have to wait a few seconds before they are ready to record. The time between the first read command from the host and the first write command from the host is the "response time." S650 and S750 series ATP cards have a response time of less than 1 second, while normal cards can take 7 to 12 seconds in real-world tests on a DVR at room temperature.

Writes 50% faster
While recording 16 MB data sequentially, ATP S650 cards take less than 0.1 second, saving 50% of writing time compared with consumer-rated cards and enabling high-speed backup without data loss.

In-house HW/FW design for precise reliability
As a specialized manufacturer with its own hardware/firmware solution, ATP can adapt to a wide range of applications to meet customers' specific application requirements and conditions.

Specifications

  SD microSD
Product Line

Premium

Superior

Premium

Superior

S750Pi

S750Sc

S650Si

S650Sc

S750Pi

S750Sc

S650Si

S650Sc

Interface

UHS-I

UHS-I

UHS-I

UHS-I

UHS-I

UHS-I

UHS-I

UHS-I

Flash Type

3D pSLC

3D pSLC

3D TLC

3D TLC

3D pSLC

3D pSLC

3D TLC

3D TLC

Form Factor

SD Card

microSD Card

Operating Temperature

-40°C to 85°C

-25°C to 85°C

-40°C to 85°C

-25°C to 85°C

-40°C to 85°C

-25°C to 85°C

-40°C to 85°C

-25°C to 85°C

Power Loss Protection Options

Firmware Based

Firmware Based

Capacity

8GB to 32GB

8GB to 32GB

32 GB to 128 GB

32 GB to 128 GB

8GB to 64GB

8GB to 64GB

32 GB to 256 GB

32 GB to 256 GB

Performance

Sequential Read (MB/s) up to

99

99

96

96

99

99

96

96

Sequential Write (MB/s) up to

78

78

62

62

82

82

65

65

Endurance (TBW)1 up to

1920

1920

640

640

3840

3840

1280

1280

Reliability
MTBF @ 25°C

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

>2,000,000 hours

Reliability
Number of Insertions

20,000 (SDA spec minimum 10,000)

20,000 (SDA spec minimum 10,000)

Others

Dimensions: L x W x H (mm)

32.0 x 24.0 x 2.1

32.0 x 24.0 x 2.1

32.0 x 24.0 x 2.1

32.0 x 24.0 x 2.1

15.0 x 11.0 x 1.0

15.0 x 11.0 x 1.0

15.0 x 11.0 x 1.0

15.0 x 11.0 x 1.0

Certifications

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

CE, FCC, UKCA, RoHS

*1 Considers highest value for sequential write. Values may vary depending on capacity, configuration and application.

 

Take advantage of our expertise in the design-in process! Enjoy the benefit of reliable processes when selecting the right SD / microSD card and secure expert advice.

Request technical information or order release samples today. We will be happy to provide you with further information upon request.

Industrial Memory Solutions

Tel.
+49 6126 590-350
Fax
+49 6126 590-139
ims.sales@glyn.de

Share this article