Reliably measure CO2 in indoor air:
World´s smallest selective CO2 sensors

03_SCD40_720px

Thanks to new energy standards and better insulation, homes and office buildings have become increasingly energy efficient. Here, active ventilation is necessary to maintain our well-being and productivity. At the same time, the indoor climate should be regulated in the most energy-efficient way possible. A decisive indicator of indoor air quality is its CO2 content.

Air exchangers and intelligent ventilation systems in commercial and residential applications use CO2 sensors. In addition, CO2 sensors play an essential role in monitoring indoor air quality and can therefore be integrated into indoor air monitors, air purifiers and smart thermostats.

SENSIRION's SCD4x are currently the world's smallest selective CO sensors.
Measuring only 10.1 x 10.1 x 6.5 mm³, they are smaller than a sugar cube. This makes them easy to integrate into compact applications.

Please activate subtitles: Options (Gear wheel) > Subtitles > English

Quickly processed via placement equipment
The SCD40 and SCD41 components are reflow solderable. They can be processed quickly and conveniently using placement systems. This saves time and money in production.

Despite their tiny size, both CO2 sensors already have an integrated temperature and humidity sensor. The wide operating voltage range is 2.4 V to 5.5 V.
This allows you to save on additional external components such as a level converter.

With its accuracy of ±50 ppm, SCD40 is ideal for CO2 traffic lights, for example.
The SCD41 operates with an accuracy of ±40 ppm and offers an additional low-power mode. It is the perfect component for high quality ventilation systems and battery powered devices.

The PASens® measuring principle

The extreme miniaturization of CO2 sensors is achieved by the unique PASens® technology. It is based on the photoacoustic measuring principle, which has been known since 1880, and has now been brought into this tiny format by SENSIRION.

Narrowband light matching the absorption bands of CO2 molecules is emitted into a predominantly closed measuring cell.

The CO2 molecules in the measuring cell absorb a part of the emitted light.
The more CO2 molecules there are in the measuring cell, the greater the absorbed energy.

Other molecules, however, do not absorb this light.
The absorbed energy stimulates the molecules to oscillate, which results in an increase in pressure in the cell due to the closed measuring cell.

The modulation of the light source causes a periodic pressure change in the measuring cell, which is measured by a microphone. The signal from the microphone thus serves as a measure of the number of CO2 molecules present in the measuring cell and is then used to calculate the CO2 concentration.

03_PASens_720px

Secure samples at GLYN and be one of the first to start.

Reserve the first samples of the SCD40 and SCD41 now. They will be available from stock GLYN from the beginning of April 2021.

Technical data can be found here:

  SCD40 SCD41
  03_SCD40_250px 03_SCD40_250px
Size 10,1 x 10,1 x 6,5 mm³
Measuring range CO2 0…40.000 ppm
Accuracy CO2 ±(50 ppm +5 % v.Mw.)
@400…2.000 ppm
±(40 ppm +5 % v.Mw.)
@400…5000 ppm
Measuring range T -10…60 °C
Measuring range RH 0…100%
Operating voltage 2,4 V…5,5 V
Power consumption 12 mA (Measurement rate = 5 s)
2,5 mA (Measurement rate = 30 s)
12 mA (Measurement rate = 5 s )
2,5 mA (Measurement rate = 30 s)
0,4 mA (Measurement rate = 5 min)
Data sheet SCD4x

Get started now with the SENSIRION starter kit and GLYN-SUPPORT.

With the SEK-SCD41 sensor in combination with the SEK-SensorBridge you have a complete plug-and-play solution. With the associated viewer software, called ControlCenter, you can display and record the measured values of the sensors directly on your PC.

SEK-SCD41-Sensor

03_SEK-SCD41-Sensor_720px

SEK-SensorBridge

03_SEK-SensorBridge_720px

The SEK-SCD41 sensor can alternatively be connected to an Arduino or Raspberry PI via the included jumper cables. The corresponding software is available free of charge and completely directly from SENSIRION. As a third option, you can solder the SCD41 Development Board to your own application using the enclosed pin headers and thus test the performance of the sensor.

Rely on 20 years of sensor expertise and start your development with GLYN-SUPPORT.
We will be happy to answer your questions personally - by phone or email.

Be one of the first to start and secure your sample and starter kit today.

Analog

Tel.
+49 6126 590-388
Fax
+49 6126 590-188
aap@glyn.de

Share this article